Adjusting/Setting the Heat-Up Tempe

Adjusting/Setting the Heat-Up Temperature

To change the set temperature on the model SP-1501, drain the water and unplug the unit. Carefully remove the four screws holding the nameplate and locate the two thermostat knurled knobs. The top knob is the thermostat for the high temperature limit setting and the bottom knob is the thermostat for the low temperature limit setting. Insert a small screwdriver into the slotted head of the thermostat knob turning clockwise to raise the temperature limit and counterclockwise to lower the temperature limit. Please note that 1/8 of a turn is approximately equal to ± 5ºF (-15ºC).

DO NOT turn the thermostat more than one full turn in either direction. Reinstall the nameplate and fill the unit with 3” (76mm) of water. During manufacturing the low temperature is preset at 160ºF (71ºC) and the high temperature at 175ºF (79ºC).

On the standard SP-1502 model, the temperature is varied by turning the thermostat knob clockwise for an increase and counterclockwise for a decrease in temperature. The temperature on low setting should approximate 140ºF (60ºC) and on high 190ºF (88ºC).

Results (Chinese Traditional) 1:

調整設置加熱溫度若要更改設定的溫度模型 SP 1501，瀝幹水分，拔下單位。仔細地卸下固定銘牌的四個螺絲並找到兩個恒溫器滾花旋鈕。頂部的旋鈕是恒溫，高溫度限制設置和底部旋鈕是溫控器，用於低溫限制設置。插入小螺絲刀開槽團長溫控器旋鈕順時針方向提高溫度上限旋轉和逆時針旋轉，降低溫度限制。請注意 1/8 圈，大約等於 ± 5ºF (-15ºC)。請不要打開恒溫器超過一整圈，在任何一個方向。重新安裝銘牌和填充單元 3 英寸 （76 毫米） 的水。在製造低溫期間預設在 160ºF (71ºC) 和 175ºF 的高溫度 (79ºC)。在標準的 SP 1502 模型中，溫度被多種多樣的轉動溫控器旋鈕，增加順時針和逆時針的溫度降低。溫度對低設置應近似 140ºF (60ºC) 和高 190ºF (88ºC)。

Results (Chinese Traditional) 2:

調整/設定升溫溫度要更改型號SP-1501的設定溫度，瀝乾水，並拔出插頭。小心取出控股銘牌的四顆螺釘，找到兩個恆溫滾花旋鈕。頂端旋鈕用於高溫限制設置的恆溫器和底部旋鈕為低溫限制設置的恆溫器。插入一個小螺絲刀插入調溫旋鈕順時針旋轉，以提高溫度上限和逆時針方向以降低溫度極限的槽頭。請注意，一轉的1/8約等於±5ºF（-15ºC）。不要把恆溫器在兩個方向上超過一整圈。重新安裝銘牌和3“的水（76毫米）填充單元。在製造低溫度在160℉（71℃）中並在175ºF（79ºC）高溫預置。在標準的SP-1502型號，溫度由在溫度下降旋鈕順時針恆溫轉動為增加和逆時針變化。低設定的溫度應接近140°F（60°C）和高190ºF（88ºC）。